Capacitor

-

Capacitor


Capacitor is a passive component which is two legs with polarity.  Some of the capacitor do not have polarity. Here we will learn about polarized capacitor. Polarized capacitor has two  polarity one is positive + another one is negative-.  To know its polarity either one leg will be long describing about positive + polarity or in capacitor there is given - minus sign in black letter exact up of that one leg.

Capacitor are found with different different storage capacity which is measured in Farads. For smaller storage, it is measured in micro-farad. The charge time of capacitor depends on its farads if  the value of farads goes high then charge time of that capacitor will be more.
Symbol Of Capacitor

Comments

Post a Comment

Popular posts from this blog

#How to make wireless spy earpiece for your exams

-
Image
In this note we will learn about how to make your own wireless earpiece at home easily.  But firstly we should learn how speaker works. You can see the gif (animation) showing how speaker works. As we know that when we apply voltage in the inductor, the inductor acts like a magnet this effect is known as electromagnet and we all know that in every magnet there are two poles(the south and north pole). Continues changing of poles in the speaker produces sound because like poles repel and unlike poles attract. You can see in the picture down below: Because of this effect our speaker produces sound. OK, I hope you have got internal working information of speaker. But till now you only learned about speaker I will tell you more than this. I will tell you one great fact i.e. as you can see the working picture of speaker you might have notice that why the inductor only moving up and down, why not the permanent magnet ? This is because the permanent magnet is fixed in one
Read more

MQ-6 Gas Sensor Interfacing with Arduino UNO and LCD

-
Image
Hello friends , this is my 4th post in blog and today we will learn about "How To Interface Gas Sensor with Arduino UNO and LCD." Before starting we will first understand "What is Gas Sensor ?" Gas sensor is a type of sensor which is capable to sense LPG gases and can give output HIGH or LOW logic signal to Arduino. In this project I am using MQ6 GAS SENSOR but we can use other also so don't worry. OK, lets look circuit in bread-board. By the way you can use pin-13 as output you can connect buzzer or led to alert. I forget to join buzzer in pin-13. Better to put buzzer. For video click the following link:- https://www.youtube.com/watch?v=BH0F8IuXSnw CODE: #include <LiquidCrystal.h> LiquidCrystal lcd(12, 11, 5, 4, 3, 2); int LED = 13;  int GAS_DO = 7;  int STATE = 0;  void setup() {   lcd.begin(16,2);   lcd.print("LPG LEAK SYSTEM");   delay(1500);   lcd.clear();   pinMode(LED,
Read more

Reed-switch Interfacing with Arduino UNO and LCD

-
Image
Hello friends , In this short tutorial I will give you knowledge about "How to interface reed switch with Arduino UNO and LCD."  Instead of reed switch we can use any other switches like tilt switch, push button, PIR sensor or something that gives output as PIR sensor gives( IR Proximity sensor ) and so on. Ok, Lets start, At first we have to learn about "What is reed switch." Reed-switch is a type of switch which is controlled by magnetic field i.e (Magnet). When magnet comes near the reed switch, it will works as close switch and vice-versa. But it is not like a " Hall Effect Sensor " Ok, take a look of this circuit:- We can use buzzer or LED in pin 13. VIDEO:   https://www.youtube.com/watch?v=PxTf_ru6LdM&t=2s CODE: #include <LiquidCrystal.h> LiquidCrystal lcd(12, 11, 5, 4, 3, 2); int LED = 13;   //pin for the LED int SWITCH = 7;   //INPUT pin where the REED-SWITCH is connected int BUTTON_STATE = 0;   //whether s
Read more